Audio Framework CTS Verifier

  • A+
所属分类:音频杂谈

This new suite of tests requires human intervention and some external hardware including a Loopback Plug, a USB reference microphone and external speakers. For devices without 3.5 mm (⅛”) headset port, the user will be able to skip the test and mark it as successful. See the sections below for details.

Loopback plug latency test


Round trip latency in audio is defined as the time it takes an audio signal to be recorded, processed and output back.

To measure round-trip latency using CTS Verifier, connect a loopback plug to the 3.5 mm (⅛”) headset connector. (If you don’t have a loopback plug, you can easily make one following the Audio Loopback Dongle instructions.

Start CTS Verifier Loopback Test Audio Framework CTS Verifier
Summary of instructions is displayed Audio Framework CTS Verifier
Report if the device has a headset port:
YES if the device under test has a physical headset port
NO if there is no headset port
Audio Framework CTS Verifier
If the answer was NO in the previous step, press Pass (green check) on the bottom of the test and finish Audio Framework CTS Verifier
If the answer was YES in the previous step, continue to connect loopback plug.
Connect a loopback plug to the headset port
Press the Loopback Plug Ready button
Audio Framework CTS Verifier
Move the slider until the signal level is greater than 60%
Press TEST
Audio Framework CTS Verifier Audio Framework CTS Verifier
Wait several seconds while the latency test is performed Audio Framework CTS Verifier
When the test is finished, results are shown
The minimum confidence level for a test to succeed is 0.6
Lower latency numbers are preferred, but no number is enforced
Audio Framework CTS Verifier
Press the Pass (green, only available if successful) or Failed (red) button to record the results. Audio Framework CTS Verifier
Audio Framework CTS Verifier

Audio frequency line test


Using a loopback plug, this test will characterize the left/right line audio output and use the mic feedback from the plug to capture audio and compute a frequency response for each channel.

A simple criterion for minimum energy expected in each band (out of four) is applied per channel.

Start CTS Audio Frequency Line Test Audio Framework CTS Verifier
Summary of instructions is displayed Audio Framework CTS Verifier
Report if the device has a headset port:
YES if the device under test has a physical headset port
NO if there is no headset port
Audio Framework CTS Verifier
If the answer was NO in the previous step, press Pass (green check) on the bottom of the test and finish Audio Framework CTS Verifier
If the answer was YES in the previous step, continue to connect loopback plug
Connect a Loopback Plug to the headset connector (see Loopback plug latency test)
Press the Loopback Plug Ready button
Audio Framework CTS Verifier
Press TEST Audio Framework CTS Verifier
Wait several seconds while the frequency tests are performed Audio Framework CTS Verifier
When the test is finished, results are shown Audio Framework CTS Verifier
Press the Pass (only available if successful) or Failed button to record the results Audio Framework CTS Verifier
Audio Framework CTS Verifier

Audio frequency speaker test


This test uses the signal captured by an external USB reference microphone to assess the frequency response of left (and right, if it exists) loudspeakers.

A reference microphone is defined as that one that delivers flat, uncolored response. They are often used for analysis and measurement equipment.

There are some inexpensive USB Reference microphones (e.g., miniDSP USB Measurement calibrated microphone, Dayton Audio UMM-6 USB Measurement Microphone), mostly used for the home theater enthusiasts to calibrate their setups.

Minimum recommended reference microphone characteristics:
Flat Frequency response on range 100 Hz - 20 kHz: +/- 2 dB
S/N ration 70 dB (A-weighted)
THD Ratio @ 1000 Hz less than 1 % at 127 dB SPL

Start CTS Audio Frequency Speaker Test Audio Framework CTS Verifier
Summary of instructions is displayed Audio Framework CTS Verifier
Connect a USB reference microphone (see Audio frequency speaker test)
Press USB REFERENCE MICROPHONE READY
Audio Framework CTS Verifier
Set up DUT (Device Under Test) in a quiet room and USB microphone 20cms perpendicular to center of screen Audio Framework CTS Verifier
Press TEST Audio Framework CTS Verifier
Wait several seconds while the frequency tests are performed Audio Framework CTS Verifier
When the test is finished, results are shown Audio Framework CTS Verifier
Press the Pass (only available if successful) or Failed button to record the results Audio Framework CTS Verifier
Audio Framework CTS Verifier

Audio frequency microphone test


This test is more involved than the previous ones. It requires the use of both: External speakers for a white noise sound source, and a USB reference microphone to use as a reference for the sound. Although this process is more involved, it can be performed with affordable, easy to get, hardware

External speakers positioned 40cm from the device are used to deliver a white noise sound source. These speakers don’t need to have a “Flat” frequency response, but need good coverage from low frequencies (100 hz) to high frequencies (20khz) is expected which is usually met by portable or medium size self powered speakers (e.g. Sony SRS-X5 portable speakers)

The key element here is that a step for calibration (using the USB reference microphone) is performed, to estimate the actual response of the speakers, thus have a solid reference to compare the built in microphone against.

Start CTS Audio Frequency Microphone Test Audio Framework CTS Verifier
Summary of instructions is displayed Audio Framework CTS Verifier
Set up DUT in a quiet room
Position the speakers 40cm perpendicular to the center of the screen of the DUT (see Audio frequency microphone test )
Audio Framework CTS Verifier
Report if the device has a headset port:
YES if the device under test has a physical headset port
NO if there is no headset port
Audio Framework CTS Verifier
If the answer was NO in the previous step, press Pass (green check) on the bottom of the test and finish Audio Framework CTS Verifier
If the answer was YES in the previous step, continue to connect external speakers.
Connect external speakers using the headphone/line out connector (remember to unplug any USB microphone)
Press EXTERNAL SPEAKERS READY
Audio Framework CTS Verifier
Press TEST 1 Audio Framework CTS Verifier
Wait several seconds for test 1 to complete. Audio Framework CTS Verifier
When test 1 is completed, results for the built in microphone are shown. Audio Framework CTS Verifier
Connect a USB Reference microphone (see Audio frequency speaker test )
Press USB REFERENCE MICROPHONE READY
Audio Framework CTS Verifier
Position USB microphone right next to built-in microphone in DUT, pointing towards external speakers Audio Framework CTS Verifier
Audio Framework CTS Verifier
Press TEST 2 Audio Framework CTS Verifier
Wait several seconds while the test 2 runs Audio Framework CTS Verifier
When test 2 is completed, results for the USB reference microphone are shown. Audio Framework CTS Verifier
Press the Pass (only available if successful) or Failed button to record the results. Audio Framework CTS Verifier
Audio Framework CTS Verifier

发表评论

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen: